Author Topic: 6.9 engine seized while cranking  (Read 351 times)

s class

  • W116 Addict
  • ****
  • Posts: 4,143
  • I'll keep the 116's, the rest can go
  • Location: Squeezing 3 W116's into a double garage
Re: 6.9 engine seized while cranking
« Reply #15 on: 08 August 2019, 01:11 PM »
I recently assisted a local main dealer with a 450SL kjet.  Someone had mad a mess of trying to fix the fuel distributor.  They had tried to install the metering barrel without any lube on the 8 orings that seal the metering slots.  This resulted in 7 of the 8 splitting.  This resulted in max unregulated delivery to those cylinders.  I advised a compression test as I was confident hydraulic lock had occurred... Three workshops had tried cranking the engine ad nauseum.  Any how, I rebuilt the fd, but we still really struggled to start the engine.  Short version of a long story

'76 6.9 Euro, '78 6.9 AMG, '80 280SE, '74 350SE, '82 500SEL euro full hydro, '83 500SEL euro full hydro , '81 500SL

s class

  • W116 Addict
  • ****
  • Posts: 4,143
  • I'll keep the 116's, the rest can go
  • Location: Squeezing 3 W116's into a double garage
Re: 6.9 engine seized while cranking
« Reply #16 on: 08 August 2019, 01:14 PM »
Short version of a long story is we then found that the left cam was timed 180 degrees out.  We corrected that, and I then got the engine to run fairly well, despite probable bent valves and probable bent rods.  The workshop manager and I were both pretty surprised to get it running that well.  But this is not the recommended way to treat an engine.

'76 6.9 Euro, '78 6.9 AMG, '80 280SE, '74 350SE, '82 500SEL euro full hydro, '83 500SEL euro full hydro , '81 500SL

s class

  • W116 Addict
  • ****
  • Posts: 4,143
  • I'll keep the 116's, the rest can go
  • Location: Squeezing 3 W116's into a double garage
Re: 6.9 engine seized while cranking
« Reply #17 on: 08 August 2019, 01:17 PM »
I've Sen 450 motors survive unregulated fuel delivery a few times, but your situation is a bit different.  Running without the meter g piston would dump fuel directly I to the intake, not via the injectors.  Remember the pump can deliver approx 2 litres a minute.  The possibility of crank case lock did occur to me, but it would take quite some time to get enough fuel to full the crank case to pass through the rings. 

'76 6.9 Euro, '78 6.9 AMG, '80 280SE, '74 350SE, '82 500SEL euro full hydro, '83 500SEL euro full hydro , '81 500SL

s class

  • W116 Addict
  • ****
  • Posts: 4,143
  • I'll keep the 116's, the rest can go
  • Location: Squeezing 3 W116's into a double garage
Re: 6.9 engine seized while cranking
« Reply #18 on: 08 August 2019, 01:19 PM »
Have you tried depressing the air mass meter flap, and opening the throttle to see if there is fuel pooled up in the intake manifold?

'76 6.9 Euro, '78 6.9 AMG, '80 280SE, '74 350SE, '82 500SEL euro full hydro, '83 500SEL euro full hydro , '81 500SL

raueda1

  • Classic
  • **
  • Posts: 304
  • W116 Enthusiast
  • Location: Salt Lake City, Utah
Re: 6.9 engine seized while cranking
« Reply #19 on: 08 August 2019, 03:17 PM »
For some findings to report:

> drained the oil.  There was a LOT in the sump but I'm not sure how much would be normal.  Oil stinks of gasoline.  It seemed to be thinned, to be sure, but not to the extent of "watery."  No metal chunks or anything came out.  I still couldn't move the crank after draining the oil.

> looked at valve timing.  The timing notches don't line up with the index lines on the post of course.  I made a little gauge to see how far offset they were from the index mark. Both sides were offset by the same amount, so it didn't look like their relationship with each other got changed.

> borescope: 
   *  looked in all the cylinders and saw nothing obvious amiss.  Stupidly I left the 90deg angle mirror at home so couldn't see everything or look at valves. I'll do that tomorrow.
   *  looked down the chain path as far as I could.  Nothing obvious - couldn't see broken teeth, metal chunks, anything like that.
   * ring gear:  poked as far as I could (which was pretty far) and couldn't see any damage.

So, it does look like there is some kind of mechanical blockage.  Or maybe hydrolock lead to something else?  The mystery continues. 

Next step, I guess, is to start >>really<< taking stuff apart.  Seems like 3 choices - from the rear (transmission), the bottom (oil sump) or top (heads).  Any further theories or suggestions are certainly welcome.  Seems like pulling the sump is probably less involved than the heads. 

Oddly, a sense of calm has overtaken me.  It's so baffling that I'm now philosophical about it.  Cheers,
-Dave
Now:  '76 6.9 Euro
Before that:  1966 230S, 1964 220SE coupe, 1977 Carrera 3.0

Randys01

  • Enthusiast
  • *
  • Posts: 98
  • W116 Enthusiast
  • Location: adelaide australia
Re: 6.9 engine seized while cranking
« Reply #20 on: 08 August 2019, 05:39 PM »
So you only got a couple  of litres out of the sump. How full is the reservoir?
However, I think the journey now takes us to timing chain/tensioner/guide issues.
In order to narrow this down I would de-tension the main chain tensioner to relieve the tension on the banana tensioner rh  bank. With the chain slack I would try to turn the cam shafts [spanner on the cam sprocket] We don't need to wiggle it far to determine the cams will turn a bit. any rotation either way tells us the top of the motor is not the culprit inc the myriad of cogs/wheels/guides n the top timing chain entourage.
Now try turning the crank pulley a smidgeon..to date it has been locked solid but if you can now get a bit of action it would indicate something is binding in the timing chain department.
Report in!

rumb

  • W116 Addict
  • ****
  • Posts: 1,306
  • MB Enthusiast
  • Location: Fort Collins, Colorado
Re: 6.9 engine seized while cranking
« Reply #21 on: 08 August 2019, 06:03 PM »
Transmission in neutral? Though even in park I think you should still be able to turn crank.

Total oil in pan I would think would be about 10 quarts with probably 2 left in the filter and cooler.

Random ideas:
can you wiggle each cam a few degrees? Grab with vice grips to see if they each move at least a little bit.  If it moves and all your upper valve train looks normal -no loose rockers -  then that would reduce odds in that area.  You may need to remove chain tensioner to allow a little chain slack.

Have you run the scope in the oil pan?
'68 250S, '77 6.9 euro, '91 300SE, '98 SL500 '14 CLS550

raueda1

  • Classic
  • **
  • Posts: 304
  • W116 Enthusiast
  • Location: Salt Lake City, Utah
Re: 6.9 engine seized while cranking
« Reply #22 on: 09 August 2019, 07:20 AM »
So you only got a couple  of litres out of the sump. How full is the reservoir?
Reservoir was full.  The gasoline thinning was very notable on the dipstick.

However, I think the journey now takes us to timing chain/tensioner/guide issues.
In order to narrow this down I would de-tension the main chain tensioner to relieve the tension on the banana tensioner rh  bank. With the chain slack I would try to turn the cam shafts [spanner on the cam sprocket] We don't need to wiggle it far to determine the cams will turn a bit. any rotation either way tells us the top of the motor is not the culprit inc the myriad of cogs/wheels/guides n the top timing chain entourage.
Now try turning the crank pulley a smidgeon..to date it has been locked solid but if you can now get a bit of action it would indicate something is binding in the timing chain department.
Report in!
This will be today's project, along with more thorough borescope exam. 
-Dave
Now:  '76 6.9 Euro
Before that:  1966 230S, 1964 220SE coupe, 1977 Carrera 3.0

raueda1

  • Classic
  • **
  • Posts: 304
  • W116 Enthusiast
  • Location: Salt Lake City, Utah
Re: 6.9 engine seized while cranking
« Reply #23 on: 09 August 2019, 08:07 AM »
Transmission in neutral? Though even in park I think you should still be able to turn crank.
Yes, in neutral.

Total oil in pan I would think would be about 10 quarts with probably 2 left in the filter and cooler.
Seemed like more than 10 quarts came out, more like 12.  Hard to measure exactly, but my 5 gallon oil drain tank was easily 2/3 full.

Random ideas:
can you wiggle each cam a few degrees? Grab with vice grips to see if they each move at least a little bit.  If it moves and all your upper valve train looks normal -no loose rockers -  then that would reduce odds in that area.  You may need to remove chain tensioner to allow a little chain slack.
Yes, Randys01 suggested similar.  Good suggestion, gentlemen.

Have you run the scope in the oil pan?
Since this is going in from the bottom I guess that's an automotive colonoscopy.  Will perform procedure today. 

All this now has me wondering about a different path.  I'm picking up the beater 6.9 early next week.  Then I could conceivably do an engine/tranny swap. Is a USA engine a simple bolt-in on a Euro chassis?  I think there are significant differences in how the oil and transmission cooling is set up.  AC might also be an issue.  I'd like to preserve the euro AC which is nicely charged with Freon 11.   USA engine would also need to be desmogged too I guess.  Anyway, I'd then have a running car to play with while the weather's still nice and sort out the original Euro engine in the meantime.  Maybe even rebuild to it's former Euro greatness.   It would also be an opportunity to redo some other stuff on the car that would otherwise be harder, like engine mounts.  This might sound kind of nuts but at some point the cumulative time & effort messing with the seized engine might exceed the effort of swapping.  And I'd eventually be pulling the donor car's engine anyway.  I haven't yet spent any time exploring this option.   Hmmmmm.
-Dave
Now:  '76 6.9 Euro
Before that:  1966 230S, 1964 220SE coupe, 1977 Carrera 3.0

rumb

  • W116 Addict
  • ****
  • Posts: 1,306
  • MB Enthusiast
  • Location: Fort Collins, Colorado
Re: 6.9 engine seized while cranking
« Reply #24 on: 09 August 2019, 11:37 AM »
I think you are best with keeping/building a Euro engine. More horsepower from different pistons and no smog.  Additionally with your euro engine you can get if you dont already have an permanent EPA waiver. Putting smog crap on will only anger your emissions department and they might demand cats which have a different floor pan to make room for them. AFAIK the heads are the same. You could build a US engine to look like a euro from the outside.

I dont remember if the parts car is euro or not, but I have a spare euro engine that parts can be obtained from if needed.
'68 250S, '77 6.9 euro, '91 300SE, '98 SL500 '14 CLS550

raueda1

  • Classic
  • **
  • Posts: 304
  • W116 Enthusiast
  • Location: Salt Lake City, Utah
Re: 6.9 engine seized while cranking
« Reply #25 on: 09 August 2019, 01:56 PM »
More info!  Loosening the chain tensioner gave enough slack to move the cams a bit - they aren't frozen.  However, the chain slack did NOT translate to the crankshaft.  It"s still stuck.

I tried to do the sump colonoscopy but failed.  The 90deg mirror on the scope is crap, crappy reflective surface, so the LED illumination is diffused and totally clouds the image.  Terrible design.

I'm not sure where this leaves me, but I doubt it's good.  I guess it means either drop the sump or pull the engine.  I'm somewhat inclined to pull engine, especially if I can do it but still leave AC compressor etc in place.  Seems like there are various possibilities that would require pulling the engine anyway, so might as well bite the bullet.  If the concensus is "yes, pull engine," then I'll start another thread on that.  I expect I'll need so guidance.  :-\

Further thoughts welcome!  Thx,
-Dave
Now:  '76 6.9 Euro
Before that:  1966 230S, 1964 220SE coupe, 1977 Carrera 3.0

Randys01

  • Enthusiast
  • *
  • Posts: 98
  • W116 Enthusiast
  • Location: adelaide australia
Re: 6.9 engine seized while cranking
« Reply #26 on: 10 August 2019, 05:30 PM »
We gave it our best shot and whilst we didn't determine a positive diagnosis we eliminated all the soft options thus justifying a major project pulldown.  Good luck.   I have read the new thread.......